Checklist: Pre-Commissioning Robotic Handling Lines

This checklist guides plant managers through verifying robotic handling lines before activation. It covers safety verification, mechanical alignment, control logic, and load testing to ensure safe and reliable integration into the production floor.
- Verify all safety interlocks and emergency stops before energizing the line.
- Check gripper alignment, load capacity, and fabric-specific handling settings.
- Confirm communication protocols and data flow between the robot and existing plant systems.
- Conduct step-by-step load testing with representative materials to catch integration gaps early.
Before a new robotic handling line goes live, the plant must confirm that the system is safe, mechanically sound, and fully integrated with existing processes. Skipping this phase leads to downtime, product damage, and safety incidents that are expensive to correct. This checklist provides a structured approach to pre-commissioning, grouped by theme, so that plant managers can verify each area systematically.
Safety Verification and Interlock Checks
The first priority is confirming that every safety device functions correctly. A robotic handling line operates in a shared environment with operators, and any failure in the safety architecture creates immediate risk.
- Test every emergency stop button along the line. Press each one and confirm that the robot halts immediately, brakes engage, and the system enters a safe state. The response should be instantaneous. There should be no lag between pressing the mushroom head and seeing the arm stop.
- Verify that light curtains, safety mats, and physical barriers activate the same safe-stop logic. Walk through the guarded zones while the robot is in motion during a low-speed test cycle. The robot must stop when a person or object interrupts the beam or presses the mat.
- Check that the safety relay or safety PLC is functioning. If a safety circuit opens, the robot should not continue any movement. Disconnect a wire from a test point on the safety chain and observe the response.
- Confirm that the emergency stop circuit is independent of the main control system. It must cut power to the drive stages even if the controller is running. This isolation ensures that a software glitch does not override a physical stop command.
- Review the lockout and tagout procedures. Ensure that maintenance personnel can isolate the robot and that no residual energy remains in pneumatic or hydraulic lines. Verify the pressure release valves and confirm the air source is shut off.
Red flag: The robot continues to move slowly after an emergency stop is pressed. This indicates a broken safety chain or a faulty brake. Stop all testing immediately.
Mechanical Alignment and Structural Integrity
The robot and its surrounding equipment must be physically stable and precisely aligned. Small errors in mounting or alignment show up as mispicks, dropped loads, or wear on mechanical components.
- Confirm that the robot base is bolted to a rigid foundation. Check for any movement when the arm reaches its full extension in all axes. Tap the base with a mallet. It should not rattle or shift.
- Inspect the mounting of the gripper or end effector. It must be square to the robot wrist and secure. Use a dial indicator to check for any play in the coupling between the wrist and the tool.
- Verify that the conveyor belts, transfer tables, and infeed stations are level and aligned with the robot’s pick and place points. Measure the height difference between the belt surface and the robot’s zero plane.
- Check the load path. Every component in the chain, from the fabric roll or bundle to the pallet or container, must support the rated load without deflection. Look for cracks in the steel structure or worn bearings on the transfer tables.
- Inspect the gripper fingers or pads. They should be clean, undamaged, and the correct material for the fabric being handled. Replace any pads that show wear or glazing, as these reduce grip strength.
Red flag: The gripper touches the edge of the bundle or the pallet. This suggests misalignment. Adjust the pick point or the station position before proceeding.
Control Logic and Program Verification
The robot program must match the physical layout and the process requirements. A well-aligned robot will fail if the logic is wrong.
- Run the program in single-step mode. Execute each move individually and confirm that the robot reaches the expected position. Observe the axis indicators on the HMI while the arm moves.
- Verify that the pick and place coordinates are correct. Mark the actual position on the floor or station and compare it to the programmed point. Use a ruler to measure the distance from the reference point to the pick location.
- Check the timing between the robot and the conveyors. The belt should stop or pause exactly when the robot arrives for loading or unloading. Measure the delay between the robot’s arrival signal and the belt stop command.
- Confirm that the program handles errors. If a pick fails, the robot should stop, signal an alarm, and not continue to the next cycle blindly. Simulate a failed pick by blocking the sensor and observe the response.
- Review the I/O mapping. Each sensor, valve, and signal must be assigned to the correct digital or analog input and output point in the controller. Check the wiring diagram against the actual connections at the terminal blocks.
Red flag: The robot picks up nothing but still moves to the next cycle. The pick confirmation sensor is either faulty or not wired correctly.
Load Testing with Representative Material
Testing with air, light, or generic items is not enough. The robot must handle the actual product under realistic conditions.
- Use the heaviest expected load for the test. This includes any packaging, wrap, or moisture that adds weight. Calculate the total weight of the fabric bundle, the wrap, and any added moisture.
- Handle the thinnest and most delicate fabric type on the line. This tests the gripper’s ability to avoid slippage or damage. Try a lightweight silk or fine cotton to see how the pads perform.
- Run the line at full production speed for a defined period. Observe the cycle time and look for any drift in position over several hundred cycles. Record the cycle time at the start and end of the test period.
- Test the line during a shift change or a simulated break. This reveals whether the robot can handle interrupted cycles without confusion or unsafe state. Stop the line for ten minutes and restart it to check the state.
- Verify that the robot can handle a misaligned or offset load. This tests the vision system or mechanical sensing, if equipped. Place a bundle slightly off-center and see if the robot adjusts its grip.
Red flag: The gripper slips on a thin fabric during a full-speed run. This is a common failure mode. Adjust the grip force, change the pad material, or add a vacuum assist before going live.
Integration and Communication Checks
The robot is not an isolated machine. It must exchange data with the plant’s control system, the material handling network, and the production management software.
- Confirm that the robot communicates with the central PLC or HMI. Every status, alarm, and cycle count should appear on the main screen. Check the communication log for any errors or timeouts.
- Verify that the robot responds to start and stop commands from the central control system. The local start button should also work as a fallback. Test both the remote and local commands to ensure they function correctly.
- Check that data from the robot, such as pick count, reject count, and fault code, is logged to the production database. Query the database after a short run to confirm the data is being recorded.
- Confirm that the network connection is stable. If the robot uses an Ethernet or fieldbus connection, test for packet loss or latency under load. Monitor the network traffic during a full-speed run.
- Review the user access levels. Operators should not be able to modify critical program parameters or safety settings. Check the access control list to ensure only authorized personnel can make changes.
Red flag: The robot runs independently but the central HMI shows no cycle count. The communication link is broken or the data mapping is wrong.
Documentation and Handover
A line is not ready for production until the documentation is complete and the operators are trained.
- Ensure that the as-built drawings, I/O list, and program backup are stored in a central location. Verify that the backup is recent and matches the current program version.
- Confirm that the operator manual is available and that the safety procedures are posted at the line. Check that the manual is up to date and that the safety signs are visible.
- Verify that maintenance staff have access to the robot’s diagnostic tools and know how to clear common faults. Test the diagnostic mode and ensure the staff can interpret the fault codes.
- Confirm that spare parts for critical components, such as gripper pads, fuses, and sensors, are on hand. Check the inventory list to ensure the parts are in good condition and stored properly.
- Sign off on the commissioning report. This document should list every test performed, the result, and any outstanding items. Ensure that all sections are signed and dated.
Red flag: The commissioning report has missing sections or unsigned fields. This is a sign that testing was not completed properly. Do not hand over the line until every item is closed.
Quick Reference: Pre-Activation Checks
| Check Area | Key Item to Verify | Red Flag |
|---|---|---|
| Safety | Emergency stop function | Robot continues to move after E-stop |
| Mechanical | Gripper alignment | Gripper touches bundle edge |
| Control | Pick point accuracy | Robot picks empty space |
| Load | Full-speed cycle test | Gripper slips on thin fabric |
| Integration | HMI data sync | No cycle count on central screen |
| Documentation | Commissioning sign-off | Unsigned or incomplete report |
Frequently asked questions
How long should the load testing phase take before full activation?
Run the line at full production speed for at least a full shift or a defined number of cycles. Observe for position drift, wear, and consistent cycle times before declaring the line ready.
Can the robot be used for production if only the light curtain is tested and not the emergency stop?
No. Both must function correctly. The emergency stop is the primary safety device for human protection, and the light curtain is a secondary layer. Both are required for a safe commissioning.
What should be done if the robot communication with the HMI is unstable?
Isolate the network connection and check for cable damage, incorrect IP settings, or protocol mismatch. Do not run the line until the data stream is reliable and all alarms appear on the central screen.
Is it safe to test the gripper with the wrong material?
No. Using the wrong material can damage the gripper or the robot's joints. Use the actual product or a close simulation that matches weight, size, and fragility.
Who should sign off on the commissioning report?
The plant manager, the maintenance lead, and the safety officer should all review and sign the document. This confirms that safety, function, and integration have been verified.


